Difference between revisions of "Sega Mega Drive/Hardware revisions"
From Sega Retro
(→Model 2: Expanded some sections) |
(Reworded information) |
||
| Line 130: | Line 130: | ||
| name=VA6.5 (PAL) | | name=VA6.5 (PAL) | ||
| image=MD1_IC_BD_M5_PAL_VA6.jpg | | image=MD1_IC_BD_M5_PAL_VA6.jpg | ||
| − | | desc= | + | | desc=The unused female DE-9 port (used for the [[Mega Modem]] in Japan) is removed. |
}} | }} | ||
{{SectionsNew | {{SectionsNew | ||
Revision as of 04:27, 23 February 2023
- Back to: Sega Mega Drive.
 |
This article needs cleanup. This article needs to be edited to conform to a higher standard of article quality. After the article has been cleaned up, you may remove this message. For help, see the How to Edit a Page article. |
Model 1
|
VA0 (JPN) |
|---|---|
Components:
Due to a last-minute issue with the VDP in H40 mode, additional clock circuitry had to be added during manufacturing. This circuitry is present on a daughterboard in the center of the PCB, and contains the master oscillator (53.6931 MHz, NTSC), a 74LS74 (dual D-type flip-flops), and two 74LS161s (4-bit counter). An issue in the hardware causes the RAM memory to not completely initialize when the game starts, causing crashes in Osomatsu-kun Hachamecha Gekijou. | |
.JPG)
|
VA1 (JPN) |
Components:
| |
|
VA2 (USA, High Definition Graphics) |
Components:
| |
|
VA3 (USA, High Definition Graphics) |
Components:
| |
|
VA4 (JPN) |
Components:
| |
|
VA4 (PAL) |
Components:
| |
|
VA5 (JPN) |
|
VA6 (JPN) |
| The first Japanese revision with the TMSS. | |
|
VA6 (USA, High Definition Graphics) |
Components:
| |
|
VA6.5 (PAL) |
| The unused female DE-9 port (used for the Mega Modem in Japan) is removed. | |
|
VA6.8 |
|
VA7 (USA) |
Components:
A function on the VDP has broken PAL 50Hz support. |
Model 2
|
VA0 (JPN) |
|---|---|
|
VA0 (PAL) |
|
VA0 (USA) |
Components:
| |
|
VA1 (USA) |
|
VA1 (PAL) |
Components:
| |
|
VA1.8 (USA) |
| PCB Printed by SKS
Components:
| |
|
VA1.8 (USA) |
| PCB Printed by CMK
Components:
| |
|
VA1.8 (PAL) |
Components:
| |
|
VA1.8 (Asia) |
Components:
| |
|
VA2 (USA) |
Components:
This revision (and the VA2.3) is the only Model 2 boards with a discrete YM2612 chip. Additional circuitry is present on the daughterboard located on the PCB, with model number 171-6961A. | |
|
VA2.3 (USA) |
Components:
This revision (and the VA2) is the only Model 2 boards with a discrete YM2612 chip. | |
|
VA3 |
Components:
| |
|
VA4 |
Components:
This is the first Mega Drive board without any discrete CPUs. Both the 68000 and Z80 are contained with the Sega 315-5960 ASIC, as well as the VDP, YM2612, and I/O controllers. |
Model 3
|
VA1 (USA) |
|---|---|
Components:
IC3 and IC4 markings are silkscreened but don't correspond to any physical ICs. | |
|
VA2 (USA) |
Components:
|