View source for Sega Mega Drive gamepad

Over the span of the [[Sega Mega Drive]]'s lifecycle, [[Sega]] released eight different types of '''Sega Mega Drive gamepads''' across its three main regions--[[NTSC]], [[PAL]] and NTSC-J. 

==Types of official gamepads==
{|class="prettytable"
!Picture||Description
|-
|[[Image:Pad_gen_v1.jpg|200px]]
|'''Sega Genesis Gamepad v1 "Model No. 1650"''': This is the first version of the NTSC gamepad for the Sega Genesis. It features three buttons—{{A}}, {{B}} and {{C}}—and has a white {{start}} button.  The arrows around the D-Pad are red, along with the indented label on each button, and the "Genesis" logo is two-toned; this color scheme matches that of the original Genesis. 
|-
|[[Image:Pad MD Gen.jpg|200px]]
|'''Sega Genesis Gamepad v2 "Model No. 1650"''': This is the second version of the NTSC gamepad for the Sega Genesis. It features three buttons—{{A}}, {{B}} and {{C}}—and has a white {{start}} button.  The red color has been dropped to match the updated "Genesis II" console design and color scheme.  It has an improved D-Pad mechanism, employing a metal ball-bearing for the pad to rock on.  This prevented the wear which plagued the original design, which used a plastic nub for the rocking motion and would eventually wear down with frequent use.
|-
|[[Image:Pad_gen_v3.jpg|200px]]
|'''Sega Genesis Gamepad v3 "Model No. 1650"''': This is the third version of the NTSC gamepad for the Sega Genesis. It features three buttons—{{A}}, {{B}} and {{C}}—and has a white {{start}} button.  It maintains the all-white color scheme of the previous revision, but again has an updated D-Pad.  This was the first iteration of Sega's 2-Piece D-Pad mechanism, used in every official subsequent Sega Saturn controller.  Rather than providing the rocking motion by a plastic nub or ball-bearing, there is a molded dome underneath the outside half of the D-Pad which allows the D-Pad to glide smoothly in a circle.  This design was also plagued with wear like the first model, eventually resulting in all four directions being able to be pressed simultaneously.
|-
|[[Image:Pad MD Gen3.jpg|200px]]
|'''Sega Genesis 6-Button Gamepad "MK-1653"''': Following the success of [[arcade]]-to-Mega Drive games such as ''Street Fighter II'', the six-button gamepad was released for a more arcade-like experience. This version of the gamepad featured {{X}}, {{Y}} and {{Z}} buttons in addition to the standard {{A}}, {{B}} and {{C}}, along with a new Mode button.  The European MegaDrive version has a reddish-orange start button to match the power and reset switches on their MegaDrive 2 console.  2-Piece D-Pad
|-
|[[Image:Pad MD JP II.jpg|200px]]
|'''JP MegaDrive 6-button pad, aka Sega Club 6 button Jr''': This is the Japanese 6-button controller.  It is noticeably smaller than the standard North American and European model.  The blue Start button matches the color scheme of the Japanese console.  Of note, its buttons were lettered in a serif style, unlike the sans-serif used previously... this font would be used again on the Sega Saturn controllers.  Due to the smaller size, the controller was also offered in North America through the "Sega Club" as it was well-suited for kids' smaller hands.  Sega Club was a program created by Sega of America to offer parents information about upcoming kid-friendly games.  Sega Club was also responsible for "edutainment" titles and games with light difficulty for young gamers; Ecco Jr was one such title.  2-Piece D-Pad
|-
|[[Image:Pad_gen3.jpg|200px]]
|'''Sega Genesis 3 Gamepad "MK-1470"''': This was the controller which was included with the [[Genesis 3]] console.  As the Genesis 3 was an economy model, manufacturer [[Majesco]] sourced them from a third-party manufacturer.  This design became the most popular design and was simply rebranded with a different logo for each third-party company who decided to market it. It features six buttons, mode and start, and includes a switch to enable rapid-fire for all 6 buttons and slow motion via rapid pause.  The design is a blatant rip-off of the Japanese 6-Button pad, but the molding does not match exactly.  2-Piece D-Pad with arguable effectiveness.
|-
|[[Image:Pad_gen_megafire.jpg|200px]]
|'''Sega Megafire Gamepad, Genesis version "Model No. 1657"''': The Sega Megafire is an official version of the then-popular "turbo" controllers of the time, which offered autofire capabilities. The gamepad offers autofire for {{A}}, {{B}} and {{C}} buttons, and has cardinal direction arrows on the d-pad in red; it also used the improved ball-bearing D-Pad mechanism. The Genesis version has the Genesis logo printed on it.
|-
|[[Image:Pad MD Megafire.jpg|200px]]
|'''Sega Megafire Gamepad, MegaDrive version''': The Sega Megafire is an official version of the then-popular "turbo" controllers of the time, which offered autofire capabilities. The gamepad offers autofire for {{A}}, {{B}} and {{C}} buttons, and has cardinal direction arrows on the d-pad in red; it also used the improved ball-bearing D-Pad mechanism. The MegaDrive version has text printed in an arc at the top of the face like the regular 3-Button controller, and obviously is lacking the Genesis logo.
|-
|[[Image:Pad MD PAL I.jpg|200px]]
|'''Sega Mega Drive Gamepad, PAL Type I''': The Sega Mega Drive Gamepad for PAL regions is extremely similar to the Sega Genesis gamepad; however, it has "Mega Drive Control Pad" and the Sega logo printed in lieu of the Sega Genesis logo.
|-
|[[Image:Pad MD JP I.jpg|200px]]
|'''Sega Mega Drive Gamepad, JP Type I''': Again, the Japanese version of the Sega Mega Drive gamepad is very much like the controllers released in the other two territories, though it has some distinct coloring differences: the {{A}}, {{B}} and {{C}} buttons are printed in red lettering instead of white, and the {{start}} button is blue. The text at the top of the controller reads "Computer Video Game Control Pad."
|-
|[[Image:Pad MD Wireless.jpg|200px]]
|'''Sega Genesis Wireless Gamepad''': Released only in the NTSC region, the Wireless Gamepad is a six-button gamepad that interfaces with the Sega Genesis by placing a receiver in the control port to receive RF signals from the wireless gamepad. The pad takes two AA batteries, which are inserted under a lid on the bottom side of the controller.  2-Piece D-Pad
|-
|[[Image:Pad MD Tectoy.jpg|200px]]
|'''Sega Mega Drive Gamepad, "MK-1470"''': A radically different design, this 6-button pad has a Turbo and slow-motion switch just like the Genesis 3 control pad.  This model had a unique D-Pad implementation; a plastic spike or pillar was raised from the rear portion of the chassis and protruded through the circuit-board inside. The point of the spire is what the D-Pad rested on for its rocking motion.  Of note is the model number on the rear of the pad, "MK-1470" which is the same as the Genesis 3 pad.  Perhaps Sega used this as a general designation for any 6-button controllers licensed from a third-party source.  The Sega logo is embossed on the rear of the controller, as well as the plug. This control pad was made by Tectoy, in Brazil.
|-
|[[Image:Pad_gen_stick1.jpg|200px]]
|'''Sega Genesis Arcade Power Stick "Model No. 1655"''': Sega's 3-button arcade stick.  Color scheme matches the original Genesis model as well as aesthetic cues like the dotted indents on the Start and turbo buttons, it has rapid-fire options for all three buttons with adjustable speed.  Of note, the rapid-fire mode is called "Megafire" just like the control pad of the same name.
|-
|[[Image:Pad_gen_stick2.jpg|200px]]
|'''Sega Genesis 6 Button Arcade Stick "Model No. MK-1627"''': Sega's 6-button arcade stick.  The design has been streamlined and modified to match the Genesis 2 redesign; though the Start and Mode buttons still have dotted indents, and the rapid-fire speed slider is still called "Megafire."  Independent turbo buttons have been replaced by switches which enable rapid-fire for their given button.
|-
|}

==Technical Information==
The chip inside the gamepad is a 74HC157. This is a high-speed CMOS quad 2-line to 1-line multiplexer.  Basically, how this works is there are two inputs ( A and B ) for every output ( Y ).  There are four groups like this.  There is one select signal for the whole chip. When the select signal is low, the output ( Y ) is the same as input A.  When the select signal is high, the output Y is the same as input B.  The pinout for the chip is as follows:

{|class="prettytable"
|-
|Pin 1||Select
|-	
|Pin 2||1A
|-	
|Pin 3||1B	
|-
|Pin 4||1Y
|-	
|Pin 5|| 2A
|-	
|Pin 6||2B	
|-
|Pin 7||2Y
|-
|Pin 8||Gnd
|-
|Pin 9||3Y
|-
|Pin 10||3B
|-
|Pin 11||3A
|-
|Pin 12||4Y
|-
|Pin 13||4B
|-
|Pin 14||4A
|-
|Pin 15||G (? must be low)
|-
|Pin 16||Vcc (+5V)
|}

All the controls are done with switches.  Up is a switch, Down is a switch, etc. Now, I will be referring to the output of these switches later on.  The output is usually high when the switch isn't pressed. When the button is pushed, the output goes low.  This is accomplished by  connecting the output to +5V through a 10k resistor.  The button is then attached between the output and ground.  It looks like this:
 
     +5V -----/\/\/------+--------- Output
               10k       |
                         |
                /        |
   Ground -----/  -------+
              button
              (normally open)
 
The line numbers are determined as follows, looking straight at the plug on
the front of the Genesis the numbers are:
<pre> 
	1 2 3 4 5
	 6 7 8 9
</pre>
 
{|class="prettytable"
|-
|Line 1||Up output.
|-
|Line 2||Down output. These are the only two direct connections.
|-
|Line 3||Pin 4 of the chip. Output 1Y.
|-
|Line 4||Pin 7 of the chip. Output 2Y.
|-
|Line 5||This line carries in +5V.  It is connected to the +5V bus line.
|-
|Line 6||Pin 9 of the chip. Output 3Y.
|-
|Line 7||Pin 1 of the chip. This carries in a select signal from the Genesis. This is a signal which varies rapidly and controls which input goes through the output
|-
|Line 8||Ground. This is connected to the Ground bus line.
|-
|Line 9||Pin 12 of the chip. Output 4Y.
|}
 
 
Now for the chips pin connections:
 
{|class="prettytable"
|-
|Pin 1||Line 7 (select)
|-
|Pin 2||Ground (1A)    
|-
|Pin 3||Left   (1B)
|-
|Pin 4||Line 3 (1Y)
|-
|Pin 5||Ground (2A)    
|-
|Pin 6||Right (2B)
|-
|Pin 7||Line 4 (2Y)
|-
|Pin 8||Ground  (GND)
|-
|Pin 9||Line 6 (3Y)
|-
|Pin 10||Button B  (3B)
|-
|Pin 11||Button A  (3A)
|-
|Pin 12||Line 9  (4Y)
|-
|Pin 13||Button C  (4B)
|-
|Pin 14||Start  (4A)
|-
|Pin 15||Ground  (G)
|-
|Pin 16||+5V  (Vcc)
|}

{{MegaDrive}}

[[Category:Mega Drive Hardware]]
[[Category:Control Pads]]