Patch

This article needs cleanup. This article needs to be edited to conform to a higher standard of article quality. After the article has been cleaned up, you may remove this message. For help, see the How to Edit a Page article.

NAME

patch - apply a diff file to an original

SYNOPSIS

patch [options] [originalfile [patchfile]]

but usually just

patch -pnum <patchfile

DESCRIPTION

patch takes a patch file patchfile containing a difference listing produced by the diff program and applies those differences to one or more original files, producing patched versions. Normally the patched versions are put in place of the originals. Backups can be made; see the -b or --backup option. The names of the files to be patched are usually taken from the patch file, but if there’s just one file to be patched it can specified on the command line as originalfile.

Upon startup, patch attempts to determine the type of the diff listing, unless overruled by a -c (--context), -e (--ed), -n (--normal), or -u (--unified) option. Context diffs (old-style, new-style, and unified) and normal diffs are applied by the patch program itself, while ed diffs are simply fed to the ed(1) editor via a pipe.

patch tries to skip any leading garbage, apply the diff, and then skip any trailing garbage. Thus you could feed an article or message containing a diff listing to patch, and it should work. If the entire diff is indented by a consistent amount, or if a context diff contains lines ending in CRLF or is encapsulated one or more times by prepending "- " to lines starting with "-" as specified by Internet RFC 934, this is taken into account.

With context diffs, and to a lesser extent with normal diffs, patch can detect when the line numbers mentioned in the patch are incorrect, and attempts to find the correct place to apply each hunk of the patch. As a first guess, it takes the line number mentioned for the hunk, plus or minus any offset used in applying the previous hunk. If that is not the correct place, patch scans both forwards and backwards for a set of lines matching the context given in the hunk. First patch looks for a place where all lines of the context match. If no such place is found, and it’s a context diff, and the maximum fuzz factor is set to 1 or more, then another scan takes place ignoring the first and last line of context. If that fails, and the maximum fuzz factor is set to 2 or more, the first two and last two lines of context are ignored, and another scan is made. (The default maximum fuzz factor is 2.) If patch cannot find a place to install that hunk of the patch, it puts the hunk out to a reject file, which normally is the name of the output file plus a .rej suffix, or # if .rej would generate a file name that is too long (if even appending the single character # makes the file name too long, then # replaces the file name’s last character). (The rejected hunk comes out in ordinary context diff form regardless of the input patch’s form. If the input was a normal diff, many of the contexts are simply null.) The line numbers on the hunks in the reject file may be different than in the patch file: they reflect the approximate location patch thinks the failed hunks belong in the new file rather than the old one.

As each hunk is completed, you are told if the hunk failed, and if so which line (in the new file) patch thought the hunk should go on. If the hunk is installed at a different line from the line number specified in the diff you are told the offset. A single large offset may indicate that a hunk was installed in the wrong place. You are also told if a fuzz factor was used to make the match, in which case you should also be slightly suspicious. If the --verbose option is given, you are also told about hunks that match exactly.

If no original file origfile is specified on the command line, patch tries to figure out from the leading garbage what the name of the file to edit is, using the following rules.

First, patch takes an ordered list of candidate file names as follows:

• If the header is that of a context diff, patch takes the old and new file names in the header. A name is ignored if it does not have enough slashes to satisfy the -pnum or --strip=num option. The name /dev/null is also ignored.

• If there is an Index: line in the leading garbage and if either the old and new names are both absent or if patch is conforming to POSIX, patch takes the name in the Index: line.

• For the purpose of the following rules, the candidate file names are considered to be in the order (old, new, index), regardless of the order that they appear in the header.

Then patch selects a file name from the candidate list as follows:

• If some of the named files exist, patch selects the first name if conforming to POSIX, and the best name otherwise.

• If patch is not ignoring RCS, ClearCase, and SCCS (see the -g num or --get=num option), and no named files exist but an RCS, ClearCase, or SCCS master is found, patch selects the first named file with an RCS, ClearCase, or SCCS master.

• If no named files exist, no RCS, ClearCase, or SCCS master was found, some names are given, patch is not conforming to POSIX, and the patch appears to create a file, patch selects the best name requiring the creation of the fewest directories.

• If no file name results from the above heuristics, you are asked for the name of the file to patch, and patch selects that name.

To determine the best of a nonempty list of file names, patch first takes all the names with the fewest path name components; of those, it then takes all the names with the shortest basename; of those, it then takes all the shortest names; finally, it takes the first remaining name.

Additionally, if the leading garbage contains a Prereq: line, patch takes the first word from the prerequisites line (normally a version number) and checks the original file to see if that word can be found. If not, patch asks for confirmation before proceeding.

The upshot of all this is that you should be able to say, while in a news interface, something like the following:

| patch -d /usr/src/local/blurfl

and patch a file in the blurfl directory directly from the article containing the patch.

If the patch file contains more than one patch, patch tries to apply each of them as if they came from separate patch files. This means, among other things, that it is assumed that the name of the file to patch must be determined for each diff listing, and that the garbage before each diff listing contains interesting things such as file names and revision level, as mentioned previously.

OPTIONS

Parameter	Description
-b or --backup	Make backup files. That is, when patching a file, rename or copy the original instead of removing it. When backing up a file that does not exist, an empty, unreadable backup file is created as a place holder to represent the nonexistent file. See the -V or --version-control option for details about how backup file names are determined.
--backup-if-mismatch	Back up a file if the patch does not match the file exactly and if backups are not otherwise requested. This is the default unless patch is conforming to POSIX.
--no-backup-if-mismatch	Do not back up a file if the patch does not match the file exactly and if backups are not otherwise requested. This is the default if patch is conforming to POSIX.
-B pref or --prefix=pref	Prefix pref to a file name when generating its simple backup file name. For example, with -B /junk/ the simple backup file name for src/patch/util.c is /junk/src/patch/util.c.
--binary	Read and write all files in binary mode, except for standard output and /dev/tty. This option has no effect on POSIX-conforming systems. On systems like DOS where this option makes a difference, the patch should be generated by diff -a --binary.
-c or --context	Interpret the patch file as a ordinary context diff.
-d dir or --directory=dir	Change to the directory dir immediately, before doing anything else.
-D define or --ifdef=define	Use the #ifdef ... #endif construct to mark changes, with define as the differentiating symbol.